How to Order a Hydraulic Pump Without a Part Number
Worn nameplate, lost documentation? You can still find the right pump without a part number: three ways to do it and a measurement sheet you can fill in on the spot.

Table of contents (10)
A typical phone call at our office goes like this: “Hello, I need a pump for an Ursus C-360.” “What's the pump number?” Silence. That's where the problem starts, because over the years several different gear pumps were fitted to the C-360 alone, depending on the year and version. Without specifics there's nothing to match, and sending a pump “by eye” ends with a return and a lost week.
That's why we always say the same thing: the nameplate comes first. The number on the nameplate solves 90% of matching problems. Below we explain where to find it and, if the nameplate is missing, how to order a pump without a part number another way.
The nameplate: where to look and what it tells you #
Every hydraulic pump leaves the factory with a nameplate. It's a metal (usually aluminium) sticker or a riveted plate with technical data. On gear pumps you'll usually find it on the side of the body or on the rear cover. On piston pumps it can also be on top of the housing.
The most important information on the nameplate is the part number (OEM number). It's a string of letters and digits that identifies one specific pump: its displacement, pressure, direction of rotation, shaft type, cover type and ports. One number = one pump, no guesswork.
What part numbers look like at different manufacturers #
- Bosch Rexroth: e.g. 0510 625 022 or AZPF-11-008RCB20MB
- Parker: e.g. PGP511A0100
- Casappa: e.g. PLP20.8D0-82E2-LEA
- Marzocchi: e.g. ALP2-D-16 or 2BK4D30R
- Kayaba (KYB): e.g. KFP2233CLWSR
- Caproni: e.g. 20C11X007N or 10A(C)6,1X053G
- Vivoil: e.g. XV2P-D/22 or X2P4502EOOA
Apart from the part number, the nameplate usually shows:
- Displacement [cm³/rev], e.g. 16, 20, 25, 32
- Working / maximum pressure [bar], e.g. 250/280
- Direction of rotation: R (clockwise) or L (anticlockwise)
- Serial number and production date
Take a clear photo of the nameplate and send it to us. That's enough for us to match the pump within minutes, without further questions. With the OEM number you can also choose between an original and a replacement.
What if there's no nameplate? #
Plate torn off, worn to nothing or painted over. It happens. Some customers then try to search by machine: “pump for a JCB 3CX, 2006”. The problem is that within a single model year, machine manufacturers fitted different pumps depending on the production batch, market or equipment version. On top of that, the pump may already have been replaced with a completely different one.
That doesn't make the machine data useless. If you give us the make, model, year and VIN, we'll try to establish what was fitted at the factory. But to be honest, we don't have catalogues for every machine in the world, and it isn't always possible. So without a nameplate, the most reliable way is to measure the pump.
How to measure a pump without a part number #
It sounds complicated, but a caliper and 10 minutes are enough. You need to establish four things: the shaft type, the front cover (mounting flange) dimensions, the ports and the direction of rotation. Below is our measurement sheet. Fill in what you can, take a screenshot and send it to us with photos of the pump from three sides (front, side, back).
Shaft #

Check the shaft first. Gear pumps have three main shaft types: tapered (1:8 taper), splined (teeth around the circumference) and parallel keyed (a smooth cylinder with a keyway). Measure the shaft diameter with a caliper. On a splined shaft, count the teeth. On a tapered shaft, measure the diameter at the thick and the thin end.
Front cover (flange) #

The front cover is the flange that bolts the pump to the drive. Measure the mounting hole spacing (dimension A, and B as well with 4 holes) and the diameter of the centring spigot (pilot). Note whether there are 2 or 4 mounting holes.
Ports #
The ports are the inlet (suction) and the outlet (pressure). If you have a thread gauge, check the thread (usually BSP). If not, measure the inner diameter of the port with a caliper.
Direction of rotation #

Check the direction of rotation looking at the pump from the shaft end. Right hand (R) = clockwise, left hand (L) = anticlockwise. Getting the direction wrong is one of the most common reasons for returns.
You don't have to fill in the whole sheet. The more data you give us, the faster we'll match the pump, but even the shaft type, its diameter and a few photos go a long way. In 9 cases out of 10 that's enough.
Common mistakes when ordering a pump #
Hundreds of orders pass through our hands every month. Some pumps come back as returns, almost always for the same reasons:
- “I want the same one I had.” Without a number or dimensions, “the same” is guesswork. Two pumps that look identical from the outside can have a different displacement (16 vs 20 cm³), a different direction of rotation or a different shaft type. You can't see it with the naked eye, and any one of these differences means the pump won't work.
- Wrong direction of rotation. A classic. A right-hand pump fitted instead of a left-hand one won't deliver oil and can be damaged on start-up. If you're not sure about the direction, write to us and we'll help you work it out.
- A shaft that doesn't fit. A 1:8 taper and a 9-tooth spline are completely different shapes. The pump can have the same hydraulic parameters, but if the shaft doesn't match the drive, it can't be fitted. That means another pump or a modified coupling, which costs extra.
- A cover that doesn't match the mounting. The bolt spacing must match to the millimetre. If the holes don't line up, the pump won't go in. That's why dimensions A, B and the pilot diameter matter so much.
- A number from an old pump that was itself a replacement. The customer gives us the number from the pump in the machine, but it's a replacement fitted five years ago by the previous owner. The replacement number doesn't always match the original OEM number. That's why we always ask: is this the original pump or a replacement? More on this in our article on replacement hydraulic pumps.
What photos of the pump to send us #
If you don't have a caliper or don't want to measure, send us at least these photos:
- Shaft end: front cover with the shaft, mounting holes visible.
- Side: ports visible, plus the nameplate if there is one.
- Back: rear cover.
- Nameplate: even if partly unreadable, sometimes part of the number can still be read.
Take the photos in good light, close up, ideally after wiping the dirt off the pump. The more we can see, the fewer questions we need to ask. We match pumps for agricultural and construction machinery, trucks, forklifts and lifts.
Can I buy a hydraulic pump without a part number?
Yes. Measure the pump (shaft, flange, ports, direction of rotation) or send us photos from three sides. That's enough for us to match an equivalent.
Where is the part number on a hydraulic pump?
On the nameplate, usually on the side of the body or on the rear cover. Sometimes it's also stamped directly on the body.
How do I check the pump's direction of rotation?
Look at the pump from the shaft end. If it turns clockwise it's right hand (R), if anticlockwise it's left hand (L).
Is the machine model enough?
Not always. Different pumps were fitted to the same model and year, and the pump may already have been replaced. The nameplate number or the pump dimensions are more reliable.



"European Agricultural Fund for Rural Development: Europe investing in rural areas.” The operation entitled: “Support for the implementation of operations under the community-led local development strategy” under the measure ‘Support for local development under the LEADER initiative’” , aimed at the Development of the enterprise through investment in the construction of a storage hall, which will allow to increase employment and improve the economic performance of the enterprise, is co-financed by the European Union under the measure “Support for local development under the LEADER initiative” of the Rural Development Program 2014-2020