How to Choose a Hydraulic Pump: 6 Parameters You Need to Know
Flow, pressure, drive, mounting, direction of rotation and oil. We go through what to check when buying a hydraulic pump and which pump type suits which job.

Table of contents (12)
Every hydraulic system needs a pump. But a pump for a tractor front loader, a pump for a tipper and a pump for a factory press are three different stories. They differ in flow, pressure, drive and how long they have to run without a break. Below we explain how to choose a hydraulic pump step by step: what a pump actually does, the 6 selection parameters and which pump type to pick.
What a hydraulic pump does (and what it doesn't) #
A hydraulic pump converts mechanical energy (from an engine, a power take-off or an electric motor) into energy in the oil. It does two things: it draws oil from the tank and pushes it into the system.
Important: a pump doesn't create pressure, it creates flow. Pressure appears only when the oil meets resistance, for example a cylinder that has to lift a loaded tipper body. The greater the load, the higher the pressure in the system. That's why choosing a pump always starts with the work the system has to do.

Whatever the pump type, every hydraulic system has similar components: a tank, filters, the pump, valves (control valve, relief valve), hoses and fittings, and actuators, i.e. cylinders or hydraulic motors. The pump has to match the rest of the system, not just the mounting point.
How to choose a hydraulic pump: 6 parameters #
1. Flow – how many litres per minute #
Flow determines how fast the cylinders move. It depends on the pump displacement [cm³/rev] and the speed it's driven at. First decide how fast the cylinder should move, then calculate the flow you need. You'll find the formulas and examples in our article on hydraulic pump flow.
2. Working and maximum pressure #
Pressure depends on the load and the cylinder area. The pump must handle the working pressure with a margin and the maximum pressure set on the relief valve. Gear pumps usually work up to about 250 bar; when you need more, piston pumps are the choice. Always check the exact values in the data sheet of the specific pump.
3. Drive and speed #
What will drive the pump? A power take-off (PTO) on a tractor or truck, the combustion engine directly, or an electric motor in a power unit? This determines the pump speed, and therefore its flow, as well as the drive power required. Every pump also has a permitted speed range that must not be exceeded.
4. Mounting: flange, shaft, ports and direction of rotation #
The pump has to fit mechanically: the flange (hole spacing and pilot diameter), the shaft type and diameter, the ports and the direction of rotation (clockwise or anticlockwise, viewed from the shaft end). Get any of these wrong and the pump either won't fit or won't work. We show how to measure them in our guide to ordering a pump without a part number.
5. Oil: temperature and viscosity #
The pump runs in oil, so oil temperature and viscosity matter. Oil that's too thick (e.g. at a cold start in winter) makes suction harder, and oil that's too thin (overheated) increases internal leakage and wear. If the machine works in frost or heat, check the viscosity range the pump can work in and choose the oil accordingly.
6. Duty cycle and noise #
Some pumps run briefly (e.g. raising a tipper body), others run all shift long (e.g. in a press or conveyor). For continuous duty, choose a pump with a margin and take care of oil cooling. Where low noise matters, for example in a factory hall, vane or gerotor pumps work better than gear pumps.
Which type of hydraulic pump should you choose? #

- External gear pump: the most popular in agricultural and construction machinery and tippers. Simple, robust, affordable and tolerant of contamination.
- Internal gear and gerotor pump: quieter and more compact, often used as a charge or lubrication pump.
- Vane pump: quiet, smooth running, common in industry and machine tools.
- Piston pump: the highest pressures and variable flow during operation. More expensive, but essential in excavators and large machines.
We write more about how these pumps work and how they differ in our article on fixed displacement pumps.
Example: a pump for a tipper #
In a tipper, the pump has to raise a loaded body, so pressure matters, but the work is short. The usual choice is a gear pump driven by a power take-off on the gearbox. To choose it, you need to know: the PTO type and speed, the required cylinder pressure, the direction of rotation and how the pump mounts on the PTO. With that data, matching the pump takes a few minutes.
Buying a replacement pump? #
If you're replacing a pump in a working machine, it's simpler: the fastest way is to match it by the number on the nameplate. You can then also choose between the original and a replacement with the same parameters.
Hydraulic pumps and parts from Frejus #
In our shop you'll find gear, piston, vane and gerotor pumps, both originals and replacements. We keep popular models in stock. We also repair piston pumps in our own service workshop. You can match the rest of the system with us too: filters, oil coolers, hydraulic motors and pump parts.
How do I choose a hydraulic pump?
Determine the flow (l/min), working pressure, drive type and speed, mounting dimensions (flange, shaft, ports, direction of rotation) and oil conditions. Based on that, choose the pump type and size.
Does a hydraulic pump create pressure?
No. A pump creates flow, and pressure builds up when the oil meets resistance, for example a loaded cylinder.
Which hydraulic pump for a tractor or a tipper?
Usually a gear pump. It's simple, robust and tolerant of contamination. The exact model depends on the drive, speed, pressure and mounting.
When should I choose a piston pump instead of a gear pump?
When you need high pressure or variable flow, for example in excavators and large machines running several functions at once.



"European Agricultural Fund for Rural Development: Europe investing in rural areas.” The operation entitled: “Support for the implementation of operations under the community-led local development strategy” under the measure ‘Support for local development under the LEADER initiative’” , aimed at the Development of the enterprise through investment in the construction of a storage hall, which will allow to increase employment and improve the economic performance of the enterprise, is co-financed by the European Union under the measure “Support for local development under the LEADER initiative” of the Rural Development Program 2014-2020