Hydraulics basics

How to Bleed a Hydraulic System: Step-by-Step Guide

Noisy, jerky operation and a drop in pressure are typical signs of air in the system. We explain how to spot it, where it comes from and how to bleed a hydraulic system safely.

SH 7 min read
How to Bleed a Hydraulic System: Step-by-Step Guide
Table of contents (5)
  1. How to tell if there's air in a hydraulic system
  2. How does air get into a hydraulic system?
  3. How to bleed a hydraulic system step by step
  4. Monitor pressure and temperature every day
  5. Hydraulic system parts from Frejus

Cylinders moving unevenly or jerking, a noisy pump and dropping pressure? Very often the culprit is air in the system. It gets in through a leaking suction line or a low oil level, or it stays in the lines after replacing a pump or cylinder. Below we explain how to spot air, where it comes from and how to bleed a hydraulic system step by step.

How to tell if there's air in a hydraulic system #

  • Uneven, “spongy” cylinder movement. Air compresses, oil doesn't. The cylinder starts with a delay, jerks or “sinks”.
  • Pump noise. Grinding, crackling or whining under load. This is often cavitation, i.e. air bubbles imploding inside the pump.
  • A drop in pressure and slower machine operation.
  • Foam in the tank or foamy oil in a sample.
  • Higher oil temperature. Compressing air in the oil heats it further.
Hydraulic oil: clear, foamy and milky – how to spot air and water in the oil
Foamy oil means air in the system. Milky oil usually means water.

A simple test: take a little oil from the tank in a glass container and let it stand for a few minutes. If foam collects at the top or you can see bubbles in the oil, there's air in the system. If the oil is cloudy and milky, there's water in the system. Bleeding won't help then; the oil needs changing and the source of water has to be found.

How does air get into a hydraulic system? #

How air gets into a hydraulic system – low oil level, leaking suction, return above oil level
The most common places where air gets into the system.
  • Low oil level. With a low level the pump draws in air along with the oil (a vortex forms above the suction).
  • A leaking suction side. A cracked or loose suction hose, a loose clamp, a damaged O-ring on a fitting. The suction side is under vacuum, so oil doesn't leak out; instead the system draws air in. That's why this kind of leak is hard to find.
  • Oil returning above the oil level. If the return line ends above the oil surface, the oil splashes into the tank and foams.
  • Worn rod seals. When a cylinder moves fast, air can get in through worn seals.
  • New installation or repair. After replacing a pump, hoses or a cylinder, air stays inside. This is the most common reason the system needs bleeding.

How to bleed a hydraulic system step by step #

SafetyOil under pressure can penetrate the skin and cause serious injury. Before working, lower the attachments to the ground and relieve the pressure in the system. Never look for leaks with your hand; use a piece of cardboard. Always follow the machine manufacturer's instructions, as the bleeding procedure differs between machines.
How to bleed a hydraulic system – 6 steps
The general bleeding sequence. Always check the machine manual for details.
  1. Top up the oil. Fill the tank to the upper mark with the correct oil and check that all fittings on the suction side are tight.
  2. Prime the pump. Before the first start of a new or replaced pump, fill it with oil (through a port or the case drain, depending on the pump type). A dry start can destroy a pump within seconds.
  3. Run at idle with no load. Let the pump run for a few minutes until it stops making noise and the oil flows evenly.
  4. Cycle the cylinders. Slowly extend and retract each cylinder over its full stroke, 5–10 times, with no load. The air returns with the oil to the tank and is released there. For a steering system, turn the wheel from lock to lock.
  5. Bleed the highest points. If a cylinder or line has a bleed screw, open it slightly at low pressure until clean oil comes out instead of bubbles, then tighten it. Do this only with the attachments lowered and the engine at idle.
  6. Check and top up. After bleeding, the oil level will drop because the oil has filled the lines and cylinders. Top up, check for foam in the tank and measure the working pressure.

If the oil contains a lot of small bubbles (it's foamy), let the machine stand for a while. The bubbles will rise to the surface in the tank on their own. If the foam quickly returns, look for the cause: a leak on the suction side or a low oil level.

ImportantBleeding removes the effect, not the cause. If air keeps coming back, check the suction line, the oil level and where the return line enters the tank. Running with air in the system destroys the pump through cavitation.

Monitor pressure and temperature every day #

Do you know the working pressure and oil temperature of your machine when everything is working well? Without these two numbers it's hard to spot a problem before it becomes serious. That's why it's worth measuring both regularly during the working day.

Pressure gauge on a hydraulic press – monitoring system pressure
A pressure gauge shows system pressure. It's worth knowing its normal reading. Photo: HelgeRieder, Wikimedia Commons (CC0).
  • Pressure: many machines have a pressure gauge or a test point, and newer ones show pressure on the controller display. If yours doesn't, it's worth fitting a gauge.
  • Temperature: the simplest way is a non-contact thermometer on the tank. Mark a spot on the tank below the minimum oil level and always measure there, so the readings are comparable.
  • Record the readings. A sudden change in pressure or temperature is a sign that something is happening: air in the system, pump wear, a clogged filter or cooler.

The normal oil temperature in working machines is usually around 80°C. We write more about what too high a temperature means and how to check if a pump is losing flow in our articles on pump failure and hydraulic pump flow.

Hydraulic system parts from Frejus #

Looking for hoses, fittings, filters or a new pump after a system repair? In our shop you'll find hydraulic pumps, pump parts, filters, oil coolers and hydraulic motors. Not sure what to choose? Write to us and we'll help you find the right parts.

How can I tell if there's air in a hydraulic system?

Cylinders move unevenly or jerk, the pump is noisy, pressure drops, and you can see foam and bubbles in the tank or in an oil sample.

How do I bleed a hydraulic system?

Top up the oil, prime the pump, run the machine at idle with no load, cycle the cylinders over their full stroke several times, bleed the highest points and top up the oil. Always follow the machine manual.

How does air get into a hydraulic system?

Most often through a low oil level, a leaking suction line, oil returning above the oil level in the tank, or after replacing a pump, hoses or a cylinder.

What does milky hydraulic oil mean?

Usually water in the oil. Bleeding won't help; the oil needs changing and the source of water has to be found.

Still getting air in the system? Describe the symptoms and we'll help find the cause and the right parts.

Contact us
Loading...