Failures and service

Hydraulic Oil Leaks: Internal and External – How to Spot Them and What to Do

An oil leak from a hydraulic pump or system costs more than the oil you top up. We show how to tell internal from external leakage, how to find a leak safely, and why a leak on the suction side lets air into the system.

SH 7 min read
Hydraulic oil leak – internal leakage inside the pump and external leakage outside
Table of contents (8)
  1. Internal and external leakage: what's the difference
  2. Internal pump leakage: symptoms
  3. External leakage: where to look
  4. How to look for a leak safely
  5. A leak on the suction side, or air in the system
  6. What a leak costs
  7. What to do when you find a leak
  8. Parts and service at Frejus

A few drops of oil under a machine are easy to ignore. But a hydraulic oil leak isn't just mess and topping up. It means lower machine performance, higher costs, risk to people and often the first sign that the pump or seals are at their limit. Below we explain how internal leakage differs from external leakage, how to recognise it and what to do.

Internal and external leakage: what's the difference #

External leakage is visible: oil escapes from the pump, a hose or a fitting to the outside. Internal leakage is hidden: oil leaks inside the pump, valve or cylinder from the high-pressure side to the low-pressure side. Nothing drips outside, but the machine loses force and speed. Both usually start with the same things: worn seals, clearances and contamination in the oil.

Internal pump leakage: symptoms #

Internal pump leakage symptoms – higher temperature, noise, slower cylinders, lower output
Internal leakage leaves no stain. It shows up as heat, noise and slower operation.

As pump parts wear, the clearances between them grow and some of the oil, instead of going into the system, returns inside the pump to the suction side. Symptoms:

  • higher oil temperature, because every internal leak turns energy into heat,
  • louder pump operation,
  • slower cylinder movement, especially under load,
  • lower output of the whole machine,
  • in the worst case, system failure.

Internal leakage can't be fixed by tightening anything. Usually the seals have to be replaced, or the pump repaired or replaced. How to check whether a pump is losing flow is described in our article on flow formulas.

External leakage: where to look #

Hydraulic pump oil leaks – shaft seal, cover, ports, body
The four places where a gear pump most often leaks.

On the pump itself, oil most often leaks at the shaft seal, from under the covers, at the ports or, in the worst case, through a cracked body. Signs of external leakage:

  • oil stains on the ground under the machine,
  • a wet, dusty pump or oil dripping from it,
  • a falling oil level in the tank,
  • oil mist while the machine is running (the most dangerous sign, see below).
Oil stain on the ground – a sign of an external leak under a machine
A stain under the machine is the simplest sign of an external leak. Photo: Greenvinet, Wikimedia Commons (CC0).

Away from the pump, leaks most often appear on hoses and fittings: at hose crimps, on loose connections, damaged O-rings and where a hose rubs against the frame.

Hydraulic hoses and fittings in a system – where leaks most often appear
Every hose and fitting connection is a potential leak point. Photo: Simon Speed, Wikimedia Commons (CC0).

How to look for a leak safely #

How to look for a hydraulic leak safely – cardboard instead of your hand
Look for a leak with your eyes and a piece of cardboard, never with your hand.
WarningHigh-pressure oil from a pinhole can penetrate the skin, even through a glove. Such an injury looks harmless but needs immediate medical attention. Never look for a leak with your hand. Oil mist around a running machine is a sign of exactly this kind of pinhole.
  1. Stop the machine, lower the attachments to the ground and release the pressure from the system.
  2. Clean oil and dust off the pump, hoses and fittings so you can see where it's leaking from.
  3. Start the machine at idle and watch from a safe distance.
  4. Hold a piece of cardboard near the suspected spot. The oil will leave a mark on it.
  5. Once you find the source, stop the machine and release the pressure before any repair.

A leak on the suction side, or air in the system #

Where air in a hydraulic system comes from – low oil level, leaking suction line, return line above the oil level
A leaking suction side doesn't drip, it draws in air.

There is a vacuum on the suction side of the pump. That's why a leaking or porous suction hose or a loose fitting doesn't leak oil outwards but draws air into the system. This kind of leak is very hard to find because it leaves no stain.

Air in the oil does three things. First, the controls become “spongy”: air compresses and oil hardly does, so the cylinders respond late and unevenly. Second, the pump starts knocking and wears faster. Third, the oil foams and heats up. Jerky movements of attachments can also be dangerous for the operator and people around the machine.

Normal, foamy and milky hydraulic oil – how to spot air and water in the oil
Foaming oil in the tank is a sign that air is getting into the system.

If the oil in the tank is foaming and the pump is louder than usual, check the tightness of the suction side and then bleed the system.

What a leak costs #

A leak that “only drips a bit” costs more than it seems:

  • the machine works slower and with less force, so productivity drops,
  • fuel or power consumption rises because the pump moves oil that does no work,
  • topping up oil and more frequent servicing are a constant cost,
  • oil on the floor or in the ground is an accident risk and a problem at inspections,
  • an ignored leak usually ends with replacing the pump and other parts.

What to do when you find a leak #

When you notice any of these signs, stop using the machine and find the cause. In most cases the culprits are worn or cracked seals, loose fittings or worn hoses. These parts need replacing, not just tightening.

  • Leak at a fitting: check the tightness and the O-ring. Don't overtighten, or you'll damage the thread.
  • Leak on a hose or crimp: the hose needs replacing. A pressure hose can't be patched.
  • Leak at the shaft seal or under a pump cover: replace the seals or the pump.
  • Internal leakage: repair or replace the pump.
TipAfter every repair, top up the oil to the correct level, bleed the system and check the repaired spot again after the first hours of work.

Parts and service at Frejus #

In our shop you'll find hydraulic pumps, repair kits and pump parts, fittings and filters. We repair piston pumps in our own service workshop. Not sure where it's leaking from or whether the pump can be repaired? Send us photos and we'll help you assess it.

How do I recognise internal leakage in a hydraulic pump?

Nothing leaks outside, but the oil is warmer than usual, the pump is louder and the cylinders move slower, especially under load.

Where does a hydraulic pump most often leak?

At the shaft seal, from under the covers, at the ports and, in the worst case, through a cracked body.

Can I look for a leak with my hand?

No. High-pressure oil can penetrate the skin. Use cardboard and always release the pressure before a repair.

Why doesn't a leaking suction hose drip?

Because there is a vacuum on the suction side. Instead of letting oil out, the hose draws in air, so the oil foams and the controls become spongy.

Machine leaking or losing power? Send us photos and we'll help find the cause and the right parts.

Contact us
Loading...