Hydraulic System Noise: Causes and How to Reduce It
A noisy pump isn't just unpleasant at work, it's also a sign that something is wearing out. We show how to find the source of hydraulic system noise and how to reduce it.

Table of contents (11)
Every hydraulic system makes some noise. The problem starts when the pump whines, something knocks or the hoses vibrate and rattle. Hydraulic system noise wears out the people around the machine, but above all it's a symptom: something is wearing, something is drawing in air or something is badly installed. Below we explain how to find the source of the noise and how to reduce it.
Before you start: safety rules #
Finding the source of noise means working near a running or recently stopped system. Always start with the machine's operating manual and the warning labels on it. In addition:
- Protective equipment: safety glasses, gloves and hearing protection near a loud machine.
- Before working on the system, stop the machine, lower the attachments to the ground and relieve the pressure.
- Never look for leaks with your hand. Oil under pressure can penetrate the skin. Use a piece of cardboard.
- Check hoses and fittings: cracks, chafing, leaks, hoses rubbing against moving parts.
- Check the oil level in the tank.
- Use a pressure gauge to check that the relief valve is set to the correct pressure.
- Don't exceed the lifting capacity of the machine or cylinder.
- After replacing parts (a hose, fitting, pump, hydraulic motor, valve, control valve or filter), check for leaks and make sure there's no air in the system.
Why noise is worth dealing with #
- Health. Long work in noise damages hearing. Workplace safety rules set a maximum permitted noise level: in Poland 85 dB for an 8-hour working day.
- Safety. In noise it's harder to hear a warning or another person.
- The machine. Noise often means vibration and cavitation, which damage the pump, lines and fittings. A part that vibrates strongly can damage the parts around it.
- Costs. A problem caught early is usually a seal or a hose. Ignored, it ends with a new pump and more parts.
Identify the sound: what each noise means #

| What you hear | Most common cause | What to check |
|---|---|---|
| High-pitched whine, louder under load | cavitation: the pump isn't getting enough oil | suction filter, suction line (too narrow, kinked), cold, thick oil |
| Knocking, rattling, uneven sound | aeration: air in the oil | oil level, leaks on the suction side, foam in the tank |
| Humming or whining that rises with speed | worn pump or motor bearings, misaligned coupling | shaft play, coupling, motor bearings |
| Vibrating, rattling lines | pressure pulsation, missing clamps, sharp bends | clamps, hose routing, accumulator |
Scroll the table sideways to see all columns.
Why a hydraulic pump gets noisy: cavitation and aeration #
The pump is the most common source of noise. It can be mechanically noisy (bearings, worn parts), but very often the culprit is the oil flowing into it.
Cavitation occurs when the pump doesn't get as much oil as it tries to draw in. Pressure drops on the suction side and vapour bubbles form in the oil. When they reach the pressure side, they collapse violently. You hear it as a whine or whistle, and every collapse tears tiny particles of material from the pump parts. Typical causes are a clogged suction filter, a suction line that is too narrow or kinked, and thick, cold oil.
Aeration is air that has got into the oil from outside: through a leaking suction side, a low oil level or foam in the tank. It causes knocking, rattling and uneven cylinder movement, and oil with air lubricates worse and heats up faster. We explain how to get air out of the system in our guide to bleeding.
How to reduce hydraulic system noise #
The goal isn't silence, it's a noise level that doesn't harm people or the machine. Often it's enough to remove one or two main sources.
1. Check the suction side and the tank #
Most cavitation and air problems start before the pump. Check the suction filter, whether the suction line is kinked or too narrow, whether the fittings and clamps are tight and whether the oil in the tank is at the correct level. With too low a level, a vortex forms above the suction and draws in air.
2. Improve hose routing #

A hose bent more sharply than its minimum bend radius allows is noisy, wears faster and restricts flow. On a suction hose, such a bend can cause pump cavitation. Instead of bending the hose at the fitting, use an elbow fitting. Secure long runs with rubber-lined clamps so that vibration isn't passed on to the machine frame.
3. Fit or check a hydraulic accumulator #
Every pump, even a new one, produces pressure pulsation, which you hear as humming and feel as vibrating lines. A hydraulic accumulator connected to the pressure line works as a shock absorber and dampens this pulsation. If there's already an accumulator in the system, check it regularly, as it loses gas pressure over time and stops working.

- Bladder: responds quickly, dampens pulsation well.
- Piston: for high pressures and large volumes.
- Diaphragm: small and compact, for smaller systems.

4. Check the electric motor in a power unit #
In power units, the electric motor itself can be the source of noise: the cooling fan, a blocked fan cover or worn bearings. Motors with a unidirectional fan are usually quieter than those with a bidirectional one. Also check the coupling between the motor and the pump: misalignment causes vibration and humming.
5. Reduce the pump speed #
The faster a pump turns, the louder it is. Where possible, a pump with a larger displacement at a lower speed gives the same flow with less noise. Before changing the pump, calculate the flow so the cylinders don't slow down.
Parts and service from Frejus #
A quiet system comes from good parts and regular inspections. In our shop you'll find hydraulic pumps, pump parts, filters and hydraulic motors, and we repair piston pumps in our own service workshop. Not sure where the noise in your machine comes from? Describe the symptoms or send a recording and we'll help find the cause.
Why is my hydraulic pump whining?
Most often because of cavitation: the pump isn't getting enough oil because the suction filter is clogged, the suction line is too narrow or kinked, or the oil is too cold and thick. A whine that rises with speed can also mean worn bearings.
What does knocking in a hydraulic system mean?
Usually air in the oil. Check the oil level, the tightness of the suction side and whether there's foam in the tank.
How do I reduce hydraulic system noise?
Remove the causes of cavitation and aeration, improve hose routing and clamping, check the accumulator and the drive motor, and reduce the pump speed where possible.
Does a hydraulic accumulator reduce noise?
Yes. An accumulator on the pressure line dampens the pressure pulsation that causes humming and vibrating lines.


"European Agricultural Fund for Rural Development: Europe investing in rural areas.” The operation entitled: “Support for the implementation of operations under the community-led local development strategy” under the measure ‘Support for local development under the LEADER initiative’” , aimed at the Development of the enterprise through investment in the construction of a storage hall, which will allow to increase employment and improve the economic performance of the enterprise, is co-financed by the European Union under the measure “Support for local development under the LEADER initiative” of the Rural Development Program 2014-2020